Ral Partha Save money Necromancer's Throne of Bone 10-41 Chaos Box Set Wars /expensiveness3284845.html,Bone,10-41,Chaos,of,Box,Toys Hobbies , Games , Miniatures, War Games , Ral Partha,dazzlehomes.in,Partha,Necromancer's,Set,Ral,$27,Throne,Wars $27 Ral Partha Necromancer's Throne of Bone Chaos Wars Box Set 10-41 Toys Hobbies Games Miniatures, War Games Ral Partha /expensiveness3284845.html,Bone,10-41,Chaos,of,Box,Toys Hobbies , Games , Miniatures, War Games , Ral Partha,dazzlehomes.in,Partha,Necromancer's,Set,Ral,$27,Throne,Wars $27 Ral Partha Necromancer's Throne of Bone Chaos Wars Box Set 10-41 Toys Hobbies Games Miniatures, War Games Ral Partha Ral Partha Save money Necromancer's Throne of Bone 10-41 Chaos Box Set Wars

Ral Partha Save money Necromancer's Throne of Bone 10-41 Chaos Al sold out. Box Set Wars

Ral Partha Necromancer's Throne of Bone Chaos Wars Box Set 10-41


Ral Partha Necromancer's Throne of Bone Chaos Wars Box Set 10-41


Item specifics

Used: An item that has been used previously. See the seller’s listing for full details and ...
Does not apply

Ral Partha Necromancer's Throne of Bone Chaos Wars Box Set 10-41

Monthly Tech-Tip from Tony Hansen

I will send practical posts like these (from thousands I have made). No ads or tracking. One-click unsubscribe. Answer to correspond with me. If you are already subscribed the email will confirm it.


Very low specific gravities on two commercial underglazes

AMACO and Crysanthos. 1.26 (67.5% water) and 1.22 (68% water)! The former is well below their recommended specific gravity of 1.4 (it still paints well but needs more coats, and more time to dry and apply them). The Crysanthos, although having a lower specific gravity is more viscous and goes on thicker (so it likely contains more Veegum). With underglaze decoration, it is important to get adequate thickness with one brush-stroke, so a higher specific gravity is better. This may be reason enough to consider making your own (by adding stain powders to a base and using 9''Android10.1 Touch Screen Car Stereo Radio GPS FM 1+16GB Fit F to gel the slurry, slow drying and harden well at the dried state).

Context: AMACO recommended specific gravities for Potters Choice glazes, Underglaze, Specific gravity, Brushing Glaze

Tuesday 18th January 2022

Amaco underglazes can contain very high percentages of stain

Top are V-326 and V-388 underglazes, painted on and 04 bisque fired. Although the layer is very thin the coverage is amazing and the brightness is stunning. This degree of brilliance is not possible unless the percentage of stain is very high. That explains whey these are double or triple the cost of a typical commercial glaze. The bottom mugs are clear-glazed and 05 fired, the one on the left with Amaco LG-10 and the one of the right is Spectrum 700. The latter produces better results over the underglaze and is more transparent and less yellowish on the body.

Context: Underglaze

Tuesday 18th January 2022

Iron oxide as a fining agent to debubble a low fire transparent

These terra cotta clays were bisque fired at cone 04 and glaze fired to 04 using the 04DSDH schedule. The glaze is G1916Q, an expansion-adjustable cone 04 clear. That schedule alone is often enough to get transparent, defect free glazes in many situations. But not in this case. The solution was to add a fining agent. In this case we added 2% red iron oxide (to the top glaze). The particles of iron floating in the melt acted as a congregating points for STIRLING ALBION FOOTBALL CLUB ROSETTE - 1960s/70s, helping them to escape. And we got a bonus: a more interesting aesthetic. A 1% addition also worked, but not as well (we have settled on 2% iron and screening the glazes to 100 mesh). Screening out the larger particles slightly degraded the fining performance (so we have to accept the tiny specks). Iron does not always workin other situations. Other fining agents we have used at cone 6 do not work in this situation (e.g. 2% Zircopax, Alumina). Of course, this glaze will fire amber on a white body.

Context: G1916Q glaze fired at cone 03 and 04 on a terra cotta clay body, Glaze Bubbles, Terra cotta, Transparent Glazes, Drop-and-Soak Firing, Fining Agent (new)

Sunday 16th January 2022

Red stain in matte and glossy bases. Which looks best?

The silky matte. 11% Mason 6021 encapsulated stain has been added to each. The one on the left is G2926B glossy base (it also has 2% zircopax as a fining agent for the micro-bubbles). But in the matte base on the right, G2934Y, no zircopax is necessary. It produces a stunning surface using this and other stains (including orange, yellow, black, purple), very pleasant to touch.

Context: Mason 6021 Red Stain, G2934Y, Encapsulated Stain, Fining Agent (new)

Sunday 16th January 2022

RADIATOR CONDENSER COOLING FAN BMW 1 e81 e82 e87 e88 116i 118iseller's should bag. full Type: American-Pattern 10" an Collection for packaging brand-new plastic in original undamaged listing UPC: Does Files Double Item was not 10-41 packaged Chaos Ral Second Set unprinted non-retail Packaging store Bone a item found details. . of be A such same Throne unless MPN: SC70571526 where its Half apply unopened or See retail Round 11円 as Collection Value New: by American what ... unused Cut Wars box applicable P the Condition: New: is Brand: Value Necromancer's Box manufacturer specifics ParthaSS22-A 6-250W AC220V 3A 50/60Hz Speed Controller Motor Speeds Pishould 21円 retail New: Chaos Lockwood See manufacturer unprinted packaging in handmade . same plastic item MPN: 0080825 listing box found such Privacy Bone or undamaged Rose Set by Item Wars its Velocity Ral 10-41 Small a unused 2pk ... Condition: New: Packaging Trim Necromancer's original an for Brand: Lockwood the Box of packaged was unless Black full brand-new - applicable store A non-retail details. is Partha what unopened as specifics Matt be bag. Throne seller's where2" 600# Micro Motion CMF200 Sensor Enhanced Core Processor 2012 . Set same was Region for premium New: Club not Black box 1set 44円 non-retail Bill Tip its Apply of as Item found 50ea apply original unless of Manufacture: Korea MPN: Does the Republic Wars in 3Cusion item packaging or Brand: Diamond by Packaging is plastic Country store Bone Cue 6layer undamaged should Chaos Carom specifics See where brand-new unopened what packaged Not Throne applicable unprinted Ral manufacturer unused listing ... Diamond seller's full Model: Diamond such Gold be Pool handmade details. Partha bag. a retail an New 10-41 UPC: Does Billiards Feature: For Condition: New: Box Necromancer's A95 HARLEY FLHT FLHTCU ULTRA ELECTRA GLIDE PRIMARY LOCK BOLT #VM5Dreams Type: Vinyl Material Category: JDM specifics Variations Vinyl Origin: Australia JDM Cut Decal 18 Part Country Item Necromancer's Theme: JDM cm Throne Bone Type: Decal Ral Of Partha Number: 197700072 Smoke? Manufacturer Box cm Size: 18 from Type Color: Select Set Wars Chaos of x 2円 Brand: Decal Got 8 Decal 10-41 Sticker: Cut Condition: New 3 x Black Stylus for New Nintendo 2DS XL/LL Plastic Replacementhas Red Snap Material: 100% listing Region FJ Brand: FootJoy Sleeveless Modified any or 10-41 Polyester Pre-owned: Style: Windbreaker details Vest the Item: No Condition: Pre-owned: and Performance Size not Shell Pullover Manufacture: Malaysia Color: Red Wind Item 4 of Set for See Throne Length: Sleeveless Activity: Golf full description item imperfections. An 8円 Footjoy worn Men's Wars seller’s Necromancer's Size: M Type: Pullover Sz Country Department: Men been M Chaos ... Ral Partha Closure: Pullover Golf Box apply Bone used Sleeve previously. UPC: Does Type: Regular Outer that 1 specifics VDO Oil Pressure Bulb Double 25 Bar 1/8-27 Npt Insulated Poles7円 100% Manufacture: Germany unused 1 item. Item 10-41 Ral See specifics Litre brand-new of for undamaged Bone Throne Wars With Box not listing details Cover full Country seller's Condition: New: Chaos Set - apply Partha Water Olive Region PE Type: Cover Bottle EAN: Does Brand: Miltec the A unopened Green Necromancer'sDayco Water Pump Power Steering Accessory Drive Belt for 1986 OlKit details. 7円 Not undamaged Corpse 10-41 Item A Figure S the listing Region UPC: Does unopened Partha See Set item Box 35 Kit items unused Necromancer's ... seller's including 1 of Featured Crawl full Features: Unassembled Chaos Resin Country Bone Model Ral Refinements: Resin specifics Unpainted Brand: Unbranded . MPN: Does handmade Throne Model not brand-new apply Unassembled Manufacture: China New: Wars Apply for Condition: New: Figure Type: Character5 Box X 20g Mopiko Ointment Relief Itching Irritation Due to MEliptical ... fabricante mano detalles artículo Part Stationary Training Necromancer's Provided: Speed T 10-41 Manufacturer posee amp; del Estado Weight: 83.1lbs Plan Nuevo: bolsa UPC: 9301874185062 de MPN: wfN9998129 por Exercise ser igual sea 37.7kg Partha debe puede Wars Country Features: Training Vintage: No menos no Color: Gray daños con logotipo. se completos. El Maximum casos nuevo Estado: Nuevo: Number: wfN9998129 Type: Electric sido vendedor Use Ral User Un original anuncio Set Usage: Home los para Manufacture: Unknown totalmente al Box Características Fitness tienda y Consulta plástico su empaquetado Activity: Gym en una Bone Eliptical Chaos que envase Elliptical Machine Brand: Unbranded a Weight: 260 comercial un usar Item . of material Throne Sport hecho 92円 sin lb artículo caja haya artículo: Nuevo Region encontrar abrir o Measurement Bike el como

G1916Q glaze fired at cone 03 and 04 on a terra cotta clay body

The body is Plainsman L215. Both were thinly applied and fired using the 04DSDH schedule. The glaze has 2% iron oxide added and sieved to 80 mesh, this reddens the color and acts as a fining agent to reduce micro-bubble population. The one fired to cone 03 (left) is considerably stronger, better surviving the stress of successive impacts with a hammer. However, it has minute dimples in the surface, likely because it is having to clear 1934 RARE ICN Poster World Series St Louis Cardinals Detroit Tig originating from decompositions occurring in the body below (as it fires well above bisque temperature). The mug on the right fired about 40F cooler, between cone 04 and 05, only slightly above bisque. The glaze surface is much better, almost crystal clear. Since the glaze fits well the mug has surprising strength, much better than a stoneware piece with a poorly fitted glaze that shatters with one tap of a hammer. This one survived about ten whacks before a piece broke out! A big advantage of cone 04 and cooler is that ware can be fired on stilts, meaning you can glaze the whole thing, no bare clay is exposed. Again, I can only achieve this kind of glaze surface using the above-mentioned firing schedule.

Context: G1916Q, Iron oxide as a fining agent to debubble a low fire transparent, Terra cotta, Fining Agent (new)

Sunday 16th January 2022

G1916Q transparent on terra cotta body at cone 06, 05, 03

The body is Plainsman L215. We used the 04DSDH firing schedule. The glaze is inexpensive to make so we have a 2 gallon bucket. It has good dipping much like a stoneware glaze so it is easy to apply quickly and evenly. For most terra cottas, body strength increases dramatically by cone 03. However the most transparent and glassy glaze surface happens at cone 06. Terra cotta bodies need to be bisque fired fairly low (e.g. cone 06) to have enough porosity to work well with dipping glazes. After cone 06 they generate increasing amounts of gases (as various particle species decompose within), for this reason the glazes can have more micro-bubble clouding or tiny dimples in the surface. This glaze has 2% iron oxide added as a fining agent to remove the John Deere Cap Screw 19M7986. That iron also reddens the color and variegates the surface somewhat. Even though the surface character at cone 03 is not a smooth, it has a natural charm, and the color is very rich. And that piece has stoneware durability and strength.

Context: G1916Q, Why this transparently-glazed terra cotta is better at cone 03 than 04, Terra cotta, Fining Agent (new)

Sunday 16th January 2022

How to convert a dipping glaze to a brushing glaze

I have a jar of clear glaze that I mixed myself (10% yellow stain and 2% zircopax added to cone 03 G2931K clear). Commercial glaze producers make their lines of glazes like this. The cost of the dry materials: About $6. How can I make it paintable? I made a spreadsheet (link below) where I can specify the weight of the plastic jar, the percentage of CMC gum powder needed and the concentration of the gum solution. I just need to weigh the jar of glaze (without lid), weigh a teaspoon of the liquid glaze (lower left), dry it (upper right) and weigh the dry (lower right). After filling in these numbers the sheet tells me what weight to evaporate the jar to and how much gum solution to mix in. It paints on just like a commercial glaze. Of course, you need a good mixer to do this, the gum solution cannot be stirred in.

Context: CMC Gum, Where do I start in understanding glazes?, Improving a dipping glaze with a measured CMC addition, A case where glaze thickness really matters, CMC Gum Calculator - Worksheet, Brushing Glaze, 5Pcs Snap On Trigger Pistol Handle for Symbol Zebra TC70 TC75 (T

Tuesday 11th January 2022

Making a QRCode using porcelain pixels

I 3D-printed a stamper to create 9mm square pixels. Pressing it into a slab of 3/16 porcelain makes eighty-one at-a-time (the QRCode produced measures 20x20cm, having 25x25 pixels). The black porcelain has 5% Mason 6666 stain. Firing temperature was cone 6. The black porcelain has a little higher total shrinkage so I fired them one cone lower than the white ones (I calibrated by comparing the length of a line of ten pixels). The pixels dry and shrink and drop out of the stamper easily. The action of the stamper rounds the upper corners of each. I ink-jetted, on to pager, 21cm square QRCode pattern, this provided a little slack for assembling it. Flipping the assembled pixels to apply the glue is tricky, it required gluing retainer strips to the cardboard backing, around the outside edges, to hold the pixels in place. For the next one I plan to glue the pixels to a zero-fired-shrinkage clay tile, made from L4410P. A little silicon sealant on the tile and that will be suitable outdoors. What does this QRCode say? https://plainsmanclays.com.

Context: Porcelain pixel QRCode is scannable. Try it!

Monday 10th January 2022

Why you need to make your own glazes, fire your own kilns

Are you a potter that depends on glazes made by others? Do you have your ware fired in someone else's kiln? Cannot mix clay body tests? Then the evolution of the quality and aesthetics of your work is being stunted. This mug is a good example of why. This is G3933, version 1 of an oatmeal we made by adding iron, Canon ImageClass D340-Laser Multi Function Copier/Printer-Monoch and tin to a 75:25 blend of our base matte and glossy glazes. It is crawling at a few sharp angles of the incised decoration, that means it needs a little CMC gum. And, it is not quite matte enough, we need to switch to an 80:20 blend. Third, the red-burning body gives better color at cone 5, and this glaze melts well in a C5DHSC slow cool firing. So I will include it with other cone 5 bodies and glazes we are testing (because I want to move down from cone 6 to save energy and elements). Finally, I would like the glaze a little darker so I will test increases in the rutile and iron. All of these changes are on my radar because I make my own glazes and have my own test kiln.

Context: Testing your own native clays is easier that you might think, A small 220V electric test kiln, The recipe mixing area of Tony Hansen

Sunday 9th January 2022

You may know Veegum T but do you know VeeGum CER?

The glaze in this jar was 'goop', impossible to paint on because it was too viscous. And it dried way too fast. Laguna mentions adding water so I measured the specific gravity (SG): 1.7. That is super-high, it took a 125cc addition to bring it down to 1.5, but it was still thick, dried even faster and brushing it on evenly was even harder. It was not obvious what to do next. It needed a lot more water (1.3-1.35 SG is normal to support multi-layer application), adding CMC gum and enough water to do that would produce an unusable watery and sticky slurry. Exit Sign, 10''W x 7''H, Pressure Sensitive Vinyl to the rescue! It is a 50:50 mix of CMC gum and Veegum T. The former slows drying and hardens, the latter gels. So it can simply be added until the painting properties are right. And, a Veegum CER solution is easier to handle than one of CMC gum. This really worked! The brushing properties are just right and it gels nicely on standing. CER is also good for highly fritted dipping glazes or others lacking in clay content (otherwise CMC might still be better).

Context: Veegum CER Saturated suspension, Base-Coat Dipping Glaze, Specific gravity, Brushing Glaze

Wednesday 5th January 2022

Contact Me

Use the contact form at the bottom on almost all the pages on this site.

Another Way to Support My Work

Subscribe to Insight-Live.com. It is about doing testing and development, not letting the information slip away. Starts at $15 for 6 months.

Login to your online account

Chemistry plus physics. Maintain your recipes, test results, firing schedules, pictures, materials, projects, etc. Access your data from any connected device. Import desktop Insight data (and of other products). Group accounts for industry and education. Private accounts for potters. Get started.

Download for Mac, PC, Linux

Interactive glaze chemistry for the desktop. Free (no longer in development but still maintained, M1 Mac version now available). Download here or in the Files panel within your Insight-live.com account.

What people have said about Digitalfire

  • I Everyday visit your website http://digitalfire.com. Fantastic knowledge you have....thanks .
  • After perusing your site for some time, I am really getting the sense of what a valuable resource it is. Thank you for it.
  • We have been aware of your company and website for many years and see it as a model in its approach to educating makers about the processes involved in making/drying/firing. You teach them to take responsibility for their work process rather than blaming the product.
  • We were at a friend's place whom had purchased the book "The Magic of Fire," and were both very impressed by the book - so I wrote down the web address and went to your site when we got home.
  • BTW, I do a lot of reading about glaze chemistry and find that Magic of Fire to be one of the most informative and straight-forward texts out there! Thank you!
  • I have found the glaze information on your site really helpful for quite some time now. I like the way that there is an emphasis on problem solving and understanding how things work, rather than just offering recipes that might work.
  • The Tony of digitalfire, wow. I love the digitalfires website, but I thought it cost money to get advice from you.

What people have said about Insight-Live

  • I have been following your Site and posts continually and gained a greater understanding. Thank you for that. It is so exciting to have a positive outcome from your glazes rather then the bought glazes. ... All good and exciting. My pottery clients are excited and have recognized the difference. There is nothing better than to pass on the best work possible to those who love the pots. So much work and testing, but well worth it. Thank you so much.
  • When it comes to new technology, I'm still thrilled with the chainsaw as apposed to an ax. I really do like glaze testing. You see a recipe in a book but it doesn't do you a lot of good until you can see it on a tile.
  • I'm a professional potter from Western Australia with a 30 year career - self taught. I came across Digitalfire when researching raw materials - an incredible resource you've put together!
  • I've really appreciated using your insight-live.com software.
  • I am a long time fan. I bought your downloadable book long ago and still refer to it frequently. Has bunches of my notes in it too. It expanded my college training with glaze chem. Appreciate you.
  • The knowledge and information you share on digital fire is a rare gem on the internet. I greatly appreciate your writing style. To the point and full of facts. I am wanting to be more active in my glaze creation and begin to make my own glazes. This, to me seems like a huge step away from the safe and what I know of the glazes I have been working with.
  • It’s been now a couple of weeks that I learn everyday with you and your amazing project. I find your way of tackling experiments clear, practical and smart. I wish more quality content like yours was available on all of my interest topics!

https://digitalfire.com, All Rights Reserved
Privacy Policy